- 您现在的位置：买卖IC网 > Sheet目录225 > FPS100032 (TDK-Lambda Americas Inc)PWR SUP FNT END 32V 992W 31A
CHAPTER 1 FPS1000 SERIES SPECIFICATIONS
FPS1000 SERIES SPECIFICATIONS
FPS1000-12
FPS1000-24
FPS1000-32
FPS1000-48
1
2
3
4
5
Rated output voltage
Output voltage set point
Output voltage range
Maximum Output Current (Refer to Fig.1)
Maximum output power
V
V
V
A
W
12
12+/-1%
10.5~13.2
72
864
24
24+/-1%
21.5~29
40
960
32
32+/-1%
28.8~38.4
31
992
48
48+/-1%
43~58
21
1008
6
7
8
Input voltage / frequency range
Maximum input current (at 100/200Vac)
Power Factor (Typ)
(*1) ---
A
---
85~265Vac continuous, 47~63Hz, Single phase
12.0/6.0
>0.98 at 115/230V and maximum output power
9
Efficiency (Typ)
(*2) %
81/83%
84/86%
84/86%
85/88%
10
11
12
13
Inrush current
Hold-up time
Maximum line regulation
Max load regulation
(*3) A
mS
(*5) ---
(*6) ---
Less than 40A
20mS typical at 100Vac input, rated output voltage and less than 80% of rated load.
0.40%
0.80%
14
Output Ripple and noise pk-pk
(*4) mV
150
200
250
300
15
16
17
18
19
20
Temperature stability
Temperature coefficient
Remote sensing
Parallel operation
Series operation
Over current protection
---
PPM/ ° C
(*7) V
(*9) ---
---
---
0.05% of rated Vout for 8hrs after 30min warm-up. Constant line, load and temperature.
200
Possible. Refer to Instruction Manual.
Possible. Refer to Instruction Manual.
Possible. Refer to Instruction Manual.
105~125% of maximum output current. Refer to Fig. 1
21
Over voltage protection
(*8) V
14.3~15.7
31~34
41.5~45.5
62~66
I C Interface
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Over temperature protection
Remote On/Off control
DC OK signal
Over-Temp. warning
AC fail signal
Auxiliary power supply
Vout voltage trimming
Front panel indicators
2
Operating temperature-models without IEC inlet
models with IEC inlet
Storage temperature
Operating humidity
Storage humidity
Cooling
Vibration
Shock
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Inverter shut down method, automatic reset.
By electrical signal or dry contact. ON: 0~0.6V or short. OFF: 2~15V or open.
Open collector signal. On when Vout>80+/-5% rated output. Max.sink current: 10mA
Open collector signal. Refer to Instruction Manual
Open collector signal. Refer to Instruction Manual
11.2~12.5VDC. 0.25A Maximum output current.
Possible, via Vout Trim pin in the I/O connector. Refer to Instruction Manual.
AC OK, DC OK, DC FAIL
Optional. Refer to Instruction Manual.
0~50 ° C: 100% load. Derate 2%/ ° C, 50 ° C to 60 ° C, Derate 2.5%/ ° C, 60 ° C to 70 ° C.
0~50 ° C: 100% load. Derate 2%/ ° C, 50 ° C to 60 ° C.
-30~85 ° C
10~90% RH, no condensation.
10~95% RH, no condensation.
By internal Fans. Variable speed control.
Built to meet ETS 300 019
Built to meet ETS 300 019
38
39
40
41
42
43
44
45
Conducted emission
Radiated emission
Applicable safety standards
Withstand voltage
Insulation resistance
Leakage current
Weight (Typ)
Size (W*H*D)
(*10)
---
---
---
---
---
mA
Kg
---
EN55022B, FCC part 15J-B, VCCI-B
EN55022B, FCC part 15J-B, VCCI-B
UL60950-1, EN60950-1
Input-Output: 3000Vrms, 1min. Input-Ground: 2000 Vrms, 1min. Output-Ground: 500Vrms,1min.
More than 100Mohm at 25 ° C and 70% RH. Output-Ground: 500Vdc
Less Than 1.1mA at 230Vac
2.0
127x41x290mm. Refer to Outline Drawing.
Notes:
*1: For cases where conformance to various safety standards (UL, EN etc.) is required,
to be described as 100-240Vac (50/60Hz).
*2: At 100/200Vac, rated load and 25 ? C ambient temperature.
*3: Not applicable for the noise filter inrush current less than 0.2mS.
*4: Measured with JEITA RC-9131A 1:1 probe, 20MHz B.W.
*5: From 85~132Vac or 170~265Vac, constant load.
*6: From No-load to Rated load, constant input voltage. Measured at the sensing point in Remote sense.
*7: Remote sensing can compensate up to 1V drop on each load wire.
*8: Inverter shut down method. Reset by AC voltage recycle or by On/Off control.
*9: Derate Maximum output power by 10% for input voltage less than 100V RMS .
*10 For FPS 1000-12/P(S), when used not with FPS-S1U or FPS-T1U
racks, an EMI suppressor clamp should be attached to the AC cable,
as close as possible to the AC inlet, to meet class B.
Vout (V)
V2
V1
Model
FPS1000 FPS1000 FPS1000 FPS1000
V/I
V1 (V)
V2 (V)
I1 (A)
I2 (A)
-12
12
13.2
66
72
-24 -32 -48
24 32 48
29 38.4 58
33 26 17.25
40 31 21
I1
I2
Iout (A)
Fig. 1: Rated output current vs output voltage
4
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
FPXLF0368-20
CRYSTAL 3.6864 MHZ 20PF SMD
FQ3225B-27
CRYSTAL 27.000 MHZ 20PF SMT
FQ5032B-18.432
CRYSTAL 18.432 MHZ 20PF SMD
FQ7050B-7.3728
CRYSTAL 7.3728 MHZ 20PF SMD
FRJ2411
CONN MOD JACK DUST CAP GREY
FRL91-23CGA3-BB79
SWITCH ROCKER DPDT 20A 12V
FRN91-27BB
SWITCH ROCKER DPDT 20A 12V
FSM100
SWITCH TACTILE SPST-NO 0.05A 12V
相关代理商/技术参数
FPS100032/P
功能描述:线性和开关式电源 1000W 32V 31A RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
FPS100032/S
制造商:TDK-Lambda Corporation 功能描述:Power Supply, 992 Watts 制造商:TDK-Lambda Corporation 功能描述:1008W,85-265VAC,32V@40A,1.61" X 5" X 11.4" - Bulk
FPS100048
功能描述:线性和开关式电源 1000W 48V 21A Rear AC Input RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
FPS1000-48
制造商:TDK 功能描述:
FPS100048/P
功能描述:线性和开关式电源 1000W 48V 21A RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
FPS100048/P-HFP
制造商:TDK-Lambda Corporation 功能描述:1008W,85-265VAC,48V@21A,1.61" X 5" X 11.4", HAZMAT - Bulk
FPS100048/PS
功能描述:线性和开关式电源 1000W 48V 21A RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
FPS100048/PS-HFP
制造商:TDK-Lambda Corporation 功能描述:1008W,85-265VAC,48V@21A,1.61" X 5" X 11.4", HAZMAT - Bulk